Show full size 924Board.org
Discussion Forum of 924.org
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 Technical FAQ924 FAQ (Technical)   Technical924 Technical Section   Jump to 924.org924.org   Jump to PCA 924 Registry924 Registry

Door handle linkage rod

 
Post new topic   Reply to topic    924Board.org Forum Index -> Body and Interior
View previous topic :: View next topic  
Author Message
dash16  



Joined: 22 Aug 2007
Posts: 255
Location: Cali Cali

PostPosted: Mon Apr 07, 2008 9:38 am    Post subject: Door handle linkage rod Reply with quote

Been trying to install the door handle linkage rod per clark's garage instructions. I can't seem to get that plastic piece to snap into the ball. Infact, I tried to hard to shove it in that I snapped the linkage piece itself.

Perhaps installation through the door handle opening is not the way to go.
Can anyone help me out on this? I may very well have to remove the metal pieces holding onto the window track!?
_________________
1987 Porsche 924S Black/Black. 5-spd.
Options: AFX C79 261 398 423 650 651 657

1987 Mercedes 190E 2.3-16 Cosworth Pearl Black/Black. 5-spd.

STUTTGART PREVAILS
Back to top
View user's profile Send private message
dash16  



Joined: 22 Aug 2007
Posts: 255
Location: Cali Cali

PostPosted: Wed Dec 31, 2008 5:55 am    Post subject: Reply with quote

so i finally got around to getting my hand around to directly push the plastic piece into the ball-thing inside the door.

it absolutely will not budge even pushing on it directly.

anyone know what i can do about this?
_________________
1987 Porsche 924S Black/Black. 5-spd.
Options: AFX C79 261 398 423 650 651 657

1987 Mercedes 190E 2.3-16 Cosworth Pearl Black/Black. 5-spd.

STUTTGART PREVAILS
Back to top
View user's profile Send private message
Pieter  



Joined: 06 Mar 2008
Posts: 53
Location: South Africa

PostPosted: Wed Dec 31, 2008 6:25 am    Post subject: Reply with quote

I had a similar problem in that my plastic piece was broken and modified. It is crucial that both the plastic peice and the ball line up correctly. What i ended up doing was:
remove the door panel
check that the plastic peice goes in behind the window rail, over the ball peice
get my hand in from behind, to try and feel when its in the right spot
put the key in the lock and turn it until it feels like it is in the right position.
then try and press it on with your hand or, if unsuccessfull by inserting a screwdriver through the hole on the inside of the door.

I have removed and reinstalled my door handle probably 5 times, and only the last time took me almost an hour, prior to that I was able to snap it easily, and I am still uncertain about what went wrong... Good luck, and hope this helps.
Back to top
View user's profile Send private message
Vince Ponz  



Joined: 02 Nov 2002
Posts: 3581
Location: Florida

PostPosted: Wed Dec 31, 2008 9:52 am    Post subject: Reply with quote

Grease the opening.

Get a tool that is shaped like a C and use it to pull the part on.

You will see this tool at Harbour Freight and comes with other screw drivers etc. Usually a 5 piece set.

Think of an ice pick with the end bent like a c.
_________________
"Never let them see you sweat"
77.5 924 modified track car
79 931 Euro stock
88 924S SE
87 911 Targa stock
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    924Board.org Forum Index -> Body and Interior All times are GMT + 10 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group