Show full size 924Board.org
Discussion Forum of 924.org
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 
 Technical FAQ924 FAQ (Technical)   Technical924 Technical Section   Jump to 924.org924.org   Jump to PCA 924 Registry924 Registry

Search found 117 matches
924Board.org Forum Index
Author Message
  Topic: 924 Wheel Thread - Please Contribute
JasonO

Replies: 267
Views: 788846

PostForum: Body and Interior   Posted: Sun Oct 09, 2016 8:52 am   Subject: 924 Wheel Thread - Please Contribute
http://i1064.photobucket.com/albums/u361/Jasonodonnell/P1110615_zpsd7alzf0c.jpg

Fitted some 20mm hubcentric spacers today on the rear, I only have 7in phone dial rims on the back for the time been, ...
  Topic: After some good advice on my cambelt please
JasonO

Replies: 18
Views: 35186

PostForum: 931 Tech.   Posted: Sun Oct 09, 2016 5:15 am   Subject: After some good advice on my cambelt please
I know It's not the wisest choise just to pop a new one on and observe, I did a small drive, checked, ran some errands checking each time, I just looked back and It was 4 years ago I changed It, and I ...
  Topic: After some good advice on my cambelt please
JasonO

Replies: 18
Views: 35186

PostForum: 931 Tech.   Posted: Sat Oct 08, 2016 8:53 am   Subject: After some good advice on my cambelt please
I wish they would publish tensioned frequency

the belt Is tensioned to 112 hertz at the moment, I am a musician by trade.
No fancy gear needed.
  Topic: After some good advice on my cambelt please
JasonO

Replies: 18
Views: 35186

PostForum: 931 Tech.   Posted: Fri Oct 07, 2016 3:12 pm   Subject: After some good advice on my cambelt please
So i got a new belt and Installed it this afternoon, turned over by hand all fine...fired up and ran gave a few revs all good so far.
I checked all the teeth THOROUGHLY there is no burs, nicks or od ...
  Topic: After some good advice on my cambelt please
JasonO

Replies: 18
Views: 35186

PostForum: 931 Tech.   Posted: Sat Oct 01, 2016 12:08 pm   Subject: After some good advice on my cambelt please
I cant remember the brand off hand but I'ts a reputable one.
I Brought It as a kit inc a new tensioner which was slightly different than the old one (needed a longer bolt),
Could well have been sit ...
  Topic: After some good advice on my cambelt please
JasonO

Replies: 18
Views: 35186

PostForum: 931 Tech.   Posted: Sat Oct 01, 2016 10:51 am   Subject: After some good advice on my cambelt please
Hope everyone's doing good?
Just had a major freak out
Lifted bonnet today just checking stuff over, there is a bit of very fine black shavings around the cam-belt pulleys both top and bottom, Not ...
  Topic: SIT DOWN, SHUT UP & WATCH THIS
JasonO

Replies: 11
Views: 6368

PostForum: General Discussions   Posted: Fri May 20, 2016 3:26 pm   Subject: SIT DOWN, SHUT UP & WATCH THIS
Great video!, haven't driven a hot Lancia yet, but Its something that appeals to me a lot.
  Topic: Clutch master cylinder replacment
JasonO

Replies: 4
Views: 3187

PostForum: General Discussions   Posted: Tue Mar 08, 2016 3:12 pm   Subject: Clutch master cylinder replacment
Ok got it cheers as always,
  Topic: Clutch master cylinder replacment
JasonO

Replies: 4
Views: 3187

PostForum: General Discussions   Posted: Sat Mar 05, 2016 5:32 am   Subject: Clutch master cylinder replacment
I've noted the clutch master cylinder is weeping slowly (not sure for how long but enough that I topped up the fluid slightly), I'd like to replace soon, and would be great to hear where others would ...
  Topic: Looking at Buying a 924
JasonO

Replies: 25
Views: 13011

PostForum: General Discussions   Posted: Tue Oct 06, 2015 5:29 pm   Subject: Looking at Buying a 924
If your up in Nelson sometime in the near future, maybe message me and we can go for I drive....I have a Turbo and have owned a NA car, I'm no expert but If you've got a job and no face tats Id certai ...
  Topic: Looking at Buying a 924
JasonO

Replies: 25
Views: 13011

PostForum: General Discussions   Posted: Fri Oct 02, 2015 7:59 am   Subject: Looking at Buying a 924
That cars been floating around for a while......A few months ago it was in Stratford, South Taranaki, I guess this person brought it and.....is now looking to move it on (so soon?), There are way nice ...
  Topic: 924 GTP project started
JasonO

Replies: 127
Views: 141481

PostForum: Performance Upgrades   Posted: Sat Jul 11, 2015 5:16 pm   Subject: 924 GTP project started
Raceboy....i was lucky enough to convince a nice young Estonian girl to stay here in N.Z with me, shes just moved in, and asked what area your from?.......nice build btw!.
  Topic: Finally got out again today!
JasonO

Replies: 0
Views: 2117

PostForum: General Discussions   Posted: Sat Jun 06, 2015 6:38 pm   Subject: Finally got out again today!
After what seems like a string of annoying problems over the last year finally got out for a good drive today....electrics cleaned up,Brass shift linkage,Mt 90,new coil,new fuel pump,window wiper moto ...
  Topic: 16" 928 dish wheels
JasonO

Replies: 14
Views: 11222

PostForum: 931 Tech.   Posted: Thu Feb 05, 2015 4:02 pm   Subject: 16" 928 dish wheels
http://i1064.photobucket.com/albums/u361/Jasonodonnell/DSC00094.jpg
  Topic: A random picture of a Porsche from 1966.
JasonO

Replies: 9
Views: 5393

PostForum: General Discussions   Posted: Fri Dec 12, 2014 8:09 am   Subject: A random picture of a Porsche from 1966.
No real historic value as this wasn't Porsche sanctioned.

Ive got that impression myself at a few Porsche club days.
 
Page 1 of 8 Goto page 1, 2, 3, 4, 5, 6, 7, 8  Next
All times are GMT + 10 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group